RAD Data comm E1 Interface Converter RIC-E1 Specifiche Pagina 61
- Pagina / 94
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
RIC-E1 Installation and Operation Manual Appendix D IR-IP Interface Module
Performing Preliminary Configuration D-7
Rescue Configuration
In case you have forgotten the IP address or the Telnet password, you will
generally not be able to view or modify the IR-IP configuration. The Rescue feature
allows you to overcome this problem.
To allow the IR-IP configuration:
1. Remove RIC-E1/R from the chassis.
2. Set section 6 of the DIP switch to ON.
3. Insert RIC-E1/R back into the chassis.
As soon as RIC-E1/R is powered on, it will respond to the default IP address
and permit entering configuration screens without password protection. All
the other configuration parameters remain unchanged.
4. After setting the parameters to desired values, remove RIC-E1/R from the
chassis and restore section 6 of the DIP switch to OFF.
D.5 Performing Preliminary Configuration
The software necessary for performing all the management and configuration
functions is stored in the IR-IP interface module, and therefore you only need a
regular Telnet host to perform all the activities described in this appendix.
A Telnet host is any computer, e.g., an IBM PC or compatible that fulfills the
following minimum requirements:
• A standard 10BaseT Ethernet interface
• A TCP/IP protocol stack, and therefore is capable of supporting IP
communication through the Ethernet interface
• Telnet client software
• A ping utility.
Outline of Preliminary Configuration
To perform the preliminary configuration procedure:
1. Connect the Telnet host to the IR-IP interface module.
2. Configure the Telnet host to enable communication with the IR-IP interface
module using the default IP parameters.
3. Establish communication with IR-IP and assign the prescribed IP address to its
LAN interface.
4. Establish again communication with IR-IP and continue the preliminary
configuration in accordance with the Quick Setup Menu section below.
- E1 Interface Converter 1
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Declaration of Conformity 10
- Quick Start Guide 11
- 2. Operating RIC-E1 12
- Contents 13
- List of Figures 14
- List of Tables 14
- Chapter 1 15
- Introduction 15
- 1.2 Physical Description 16
- 1.3 Functional Description 17
- 1.4 Technical Specifications 18
- Chapter 2 21
- Installation and Setup 21
- 2.3 Configuring RIC-E1 22
- Configuring RIC-E1 2-3 23
- Connecting the Interfaces 24
- Connecting the Power 25
- 2-6 Configuring RIC-E1 26
- Chapter 3 27
- Operation 27
- 3.2 Operating Instructions 28
- Chapter 4 29
- Troubleshooting and 29
- Diagnostics 29
- 4.2 Troubleshooting 30
- Chapter 5 31
- RIC-E1/R Card 31
- 5-2 ASM-MN-214 Card Cage 32
- 5.2 Power Supply 33
- 5.3 RIC-E1/R Front Panel 34
- CHASS-GND 36
- TX&RX CODE 36
- TIMING SEL 36
- Warning 38
- Appendix A 39
- Interface Connector Wiring 39
- [Function] 40
- [Signal 40
- Timing] 40
- A.3 Line Interface Connector 41
- Appendix B 43
- IR-ETH Interface Module 43
- 10BA SE-T 43
- B.2 Technical Specifications 45
- Setting the DIP Switch 46
- LED Indicators 46
- Connecting the LAN 47
- C.1 IR-ETH/QN Options 49
- C.2 Technical Specifications 51
- Setting the DIP Switches 52
- Appendix D 55
- IR-IP Interface Module 55
- D.2 Technical Specifications 56
- D.3 Physical Description 56
- RIC-E1/IP 57
- IR-IP LEDs 58
- IR-IP Controls 58
- Rescue Configuration 61
- Connecting the Telnet Host 62
- What to Do If 64
- D.6 IR-IP Management Utility 65
- D.7 Quick Setup Menu 66
- LAN IP Address 67
- LAN IP Mask 67
- WAN IP Address 67
- WAN IP Mask 67
- Default Gateway 67
- RIC-E1 with IR-IP 68
- DHCP Server 68
- LAN IP Address: 192.168.1.2 68
- Mask: 255.255.255.248 68
- IP Network 68
- D.8 Management Access Menu 69
- D.9 Advanced Setup Menu 70
- Interface Parameters Menu 71
- D-18 Advanced Setup Menu 72
- Protocol Field Compression 73
- Authentication Protocol 73
- Multicast IP Menu 74
- Multicast Forwarding 75
- D.10 Device Control Menu 76
- New Software Download Menu 77
- Viewing Error Log Screen 77
- Erasing Configuration 78
- Resets Menu 78
- D.11 View Menu 79
- ARP Tables 80
- Statistics Screen 81
- Using the Ping Function 83
- D.14 Erasing IR-IP Software 84
- Erasing Application Software 85
- Downloading New Software 85
- E.1 Introduction 87
- EXT INT/LBT 88
- INT/LBT Clock Mode 89
- Customer Response Form 91
- Error Report 92
Prodotti e manuali riguardandi Networking RAD Data comm E1 Interface Converter RIC-E1
Networking RAD Data comm 100 Specifiche
(318 pagine)
(318 pagine)
Networking RAD Data comm ASMi-52L Specifiche
(153 pagine)
(153 pagine)
Networking RAD Data comm T1 Specifiche
(48 pagine)
(48 pagine)
Networking RAD Data comm MBE10-8D Specifiche
(50 pagine)
(50 pagine)
Networking RAD Data comm HCD-E1 Specifiche
(150 pagine)
(150 pagine)
Networking RAD Data comm MiRICi-E3T3 Specifiche
(106 pagine)
(106 pagine)
Networking RAD Data comm 100 Specifiche
(9 pagine)
(9 pagine)
Networking RAD Data comm ASM-60 Specifiche
(90 pagine)
(90 pagine)
Networking RAD Data comm ASM-10/8 Specifiche
(56 pagine)
(56 pagine)
Networking RAD Data comm ASMi-52CQ Specifiche
(100 pagine)
(100 pagine)
Networking RAD Data comm 146 Manuale Utente
(202 pagine)
(202 pagine)
Networking RAD Data comm LA-210 Specifiche
(210 pagine)
(210 pagine)
Andrew James Domestic Vacuum Sealer Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Kleine Küchengeräte Andrew James Domestic Vacuum Sealer.
Wir stellen 1 PDF-Handbücher Andrew James Domestic Vacuum Sealer zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Betriebsanleitung
Commenti su questo manuale